Join me in building a custom LED light bar mount for my truck. I start with a drawing and some pieces of metal and make it into a fully functional rig to hold my 42in LED Light Bar. The rack consists of bed rails, a headache rack, and a roof rack, all-in-one, to hold the light bar. I use 1.5in .083 wall square tubing, a 90amp harbor freight flux welder, a grinder, and a cutoff wheel to get the job done.
Episode 1:https://youtu.be/qp9L00SMSHQ?list=PLvKbarVtwhUvttF8SaaIrpSYX4walXQCb
Episode 3: How to Wire an LED Light Bar Properly:
https://youtu.be/b8GY69Ci7l4?list=PLvKbarVtwhUvttF8SaaIrpSYX4walXQCb
Here is where I got the 42in Wurton lightbar: http://amzn.to/29OF8s0
Welder I used to make my rig: https://amzn.to/2vpDKc6
Grinder I used: http://amzn.to/29OEHOG
Cutoff Wheel I used: http://amzn.to/29VPFRH
Herculiner Paint: http://amzn.to/2ag9z8J
Tap and Die Set I used to thread the bolt into the metal: http://amzn.to/29IUtsJ
Become a ChrisFix Subscriber→ http://www.youtube.com/subscription_center?add_user=paintballoo7
Instagram→ https://www.instagram.com/chrisfixit
Facebook→ https://www.facebook.com/chrisfix8
Website → http://www.ChrisFixed.com
My Channel Home Page → https://www.youtube.com/ChrisFix
**If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday**
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
Episode 1:https://youtu.be/qp9L00SMSHQ?list=PLvKbarVtwhUvttF8SaaIrpSYX4walXQCb
Episode 3: How to Wire an LED Light Bar Properly:
https://youtu.be/b8GY69Ci7l4?list=PLvKbarVtwhUvttF8SaaIrpSYX4walXQCb
Here is where I got the 42in Wurton lightbar: http://amzn.to/29OF8s0
Welder I used to make my rig: https://amzn.to/2vpDKc6
Grinder I used: http://amzn.to/29OEHOG
Cutoff Wheel I used: http://amzn.to/29VPFRH
Herculiner Paint: http://amzn.to/2ag9z8J
Tap and Die Set I used to thread the bolt into the metal: http://amzn.to/29IUtsJ
Become a ChrisFix Subscriber→ http://www.youtube.com/subscription_center?add_user=paintballoo7
Instagram→ https://www.instagram.com/chrisfixit
Facebook→ https://www.facebook.com/chrisfix8
Website → http://www.ChrisFixed.com
My Channel Home Page → https://www.youtube.com/ChrisFix
**If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday**
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
chris can you put your wires in zipties
Those welds are super ugly! They're still 2000% better weld than what i can lay down though. Love it!
What about wiring the light correctly. Part 3.
No one needs to be a perfect welder if you have a grinder
Thanks for sharing this video and information. I just stumbled upon your channel today.
I appreciate the detailed explanations. I am inspired to try some new techniques and gain skills along the way. I’m 74 years old and had a couple of Strokes in August 2022. I currently am recovering & receiving therapy. Unfortunately I am becoming aware that body is not functioning as well as it used.
How is it held to the truck securely?
It looks good as a light bar but you can't carry any thing above and behind the lights no cargo. Love your show.
Fix fix
Hey Chris fix please draw a face of a of a real man come on
Hey Chris …….I have a question
Does this still work for a double caB truck??
7yrs later that video is still🔥🔥
Sick
It looks clean, but I would have places the light bar further forward and added spikes for the zombies
I want a rack like that for my truck